Energy storage techniques

 With emerging trend of solar power the most fundamental concern is the climate dependency of the power generation. That is , power is generated when the sun is available and not necessarily when the demand is high. The electric power grid operates based on a delicate balance between supply (generation) and demand (consumer use). One way to help balance fluctuations in electricity supply and demand is to store electricity during periods of relatively high production and low demand, then release it back to the electric power grid during periods of lower production or higher demand. In some cases, storage may provide economic, reliability, and environmental benefits. Depending on the extent to which it is deployed, electricity storage could help the utility grid operate more efficiently, reduce the likelihood of brownouts during peak demand, and allow for more renewable resources to be built and used.

Energy can be stored in a variety of ways, including:

  • Pumped hydroelectric. Electricity is used to pump water up to a reservoir. When water is released from the reservoir, it flows down through a turbine to generate electricity.
  • Compressed air. Electricity is used to compress air at up to 1,000 pounds per square inch and store it, often in underground caverns. When electricity demand is high, the pressurized air is released to generate electricity through an expansion turbine generator.
  • Flywheels. Electricity is used to accelerate a flywheel (a type of rotor) through which the energy is conserved as kinetic rotational energy. When the energy is needed, the spinning force of the flywheel is used to turn a generator. Some flywheels use magnetic bearings, operate in a vacuum to reduce drag, and can attain rotational speeds up to 60,000 revolutions per minute.
  • Batteries. Similar to common rechargeable batteries, very large batteries can store electricity until it is needed. These systems can use  lithium ion, lead acid, lithium iron or other battery technologies.
  • Thermal energy storage. Electricity can be used to produce thermal energy, which can be stored until it is needed. For example, electricity can be used to produce chilled water or ice during times of low demand and later used for cooling during periods of peak electricity consumption. 

In addition to these technologies, new technologies are currently under development, such as flow batteries, supercapacitors, and superconducting magnetic energy storage.

Environmental Impacts of Electricity Storage

Storing electricity can provide indirect environmental benefits. For example, electricity storage can be used to help integrate more renewable energy into the electricity grid. Electricity storage can also help generation facilities operate at optimal levels, and reduce use of less efficient generating units that would otherwise run only at peak times. Further, the added capacity provided by electricity storage can delay or avoid the need to build additional power plants or transmission and distribution infrastructure.

Potential negative impacts of electricity storage will depend on the type and efficiency of storage technology. For example, batteries use raw materials such as lithium and lead, and they can present environmental hazards if they are not disposed of or recycled properly. In addition, some electricity is wasted during the storage process. 

Sri lanka also will face some challenges with regards to the storage with that now may be a good time to study on these topics more in details.

Source: https://www.epa.gov/energy/electricity-storage

Comments

Post a Comment

Popular posts from this blog

ROOFTOP SOLAR - STANDARDS of the country

Image
Standards Code Specification Description International Standards Mandatory requirement SLS 1522 (2016) Sri Lanka Standards Code of Practice for Grid Connected PV Power Systems. This Technical Standards defines the minimal information and documentation required to be handed over to a customer following the installation of a grid connected PV system. This standard also describes the installation, testing and commissioning procedure and documentation expected to verify the safe installations and correct operation of the system. It is for use by system designers and installers of grid connected net energy metered solar PV systems as a template to provide effective documentation to a customer. By detailing the expected installation, testing & commissioning procedure, it is also intended to assist in the verification / inspection of a grid connected PV system after installation and for subsequent re-inspection, maintenance or modifications. Additional, it is written for grid con...
Read more

Solar Battery System Types - AC Vs DC Coupled

Image
December 20, 2019 Jason Svarc  What is AC or DC coupling? AC or DC coupling refers to the way solar panels are coupled or linked to an energy storage or battery system. The type of electrical connection between a solar array and a battery can be either Alternating Current (AC) or Direct Current (DC). AC is when the current flows rapidly forward and backwards (this is what the electricity grid uses to operate) and DC is where the current flows in one direction. Most electronic circuits use DC, while solar panels produce DC, and batteries store DC energy. However, most electrical appliances operate on AC. This is why all homes and businesses have AC circuits. DC can be converted to AC using an inverter but, as explained below some energy is always lost in the conversion. The Solar battery evolution Simple DC coupled solar battery systems were once used only for remote power systems and off-grid homes, but over the last decade inverter technology advanced rapidly and led to the devel...
Read more